Search:

Type: Posts; User: kahalary-harry

Search: Search took 0.01 seconds.

  1. Got it

    Hi again hrant

    Thank you, that worked. I used the existing SIP tunnel (I assumed there can only be on tunnel between 2 devices) just added a new entry in the call routing table. Now I can go home...
  2. Hi hrant Thanks for the feedback, I will give...

    Hi hrant

    Thanks for the feedback, I will give that a go and post back once I have it running.

    Thank you and regards
  3. How do I share 1 FXO with 2 Quadro 2xi?

    Hi guys

    I searched around the various forums, but did not get any hits on my question.

    Scenario:
    First Quadro 2xi is the master device (5.2.8), uses the onboard ISDN trunk, and also uses my...
  4. Replies
    2
    Views
    2,371

    Hi Kevin Thanks mate, I've made the changes,...

    Hi Kevin

    Thanks mate, I've made the changes, and it works properly now :). One thing to knock off my to do list.

    Cheers mate!
  5. Replies
    2
    Views
    2,371

    Outbound calls from 2xi ISDN to FXO

    Hi all

    I found two previous threads that kind of touched on this question, but I am not sure that I understand correctly how it works.

    I have a 2xi with a BRI trunk, I use "0" as a pre-fix to...
  6. Replies
    1
    Views
    3,262

    I got hold of a colleague from another co today,...

    I got hold of a colleague from another co today, we had a good look at the 2X: it was missing a routing table / pattern causing the outbound calls to fail. I don't recall seeing a matching one there...
  7. Replies
    1
    Views
    3,262

    FXO and 2X - losing config?

    Have a 2X and and FXO (with 3 analogue trunks), they have been working without any issues for ages. Suddenly last week one could make no out going calls, and not receiving incoming calls. However...
  8. Replies
    2
    Views
    2,706

    Just a general comment on presenting caller ID to...

    Just a general comment on presenting caller ID to agents before they answer: I've supported call centers for many years (on other PBX brands), and we have observed "work avoidance" on the part of...
  9. Replies
    4
    Views
    2,375

    I think he means pin codes for extensions - I...

    I think he means pin codes for extensions - I have not implemented it, so can't add any value to this post (blush)
  10. Please make this a sticky :)

    Please make this a sticky :)
  11. Replies
    2
    Views
    3,025

    Sorry to barge in here, and I admit I have not...

    Sorry to barge in here, and I admit I have not looked at the Quadro Hot Desking feature, but from my experience with other brands, hot desking implies that your extension number follows you...
  12. Replies
    13
    Views
    7,405

    Sadly the problem persists for those of us who...

    Sadly the problem persists for those of us who have to use Telkom as an ISP... bummer, but it's not an Epygi forum or a browser problem.

    I have a theory on this, but might be best not to say it...
  13. Poll: I think the idea it self is great, but may not be...

    I think the idea it self is great, but may not be of much use to users outside the USA? However it will probably provide a solid template to install from when setting up one's own ITSP accounts with...
  14. Replies
    41
    Views
    34,847

    Here is a little add on: I found about 3 of those...

    Here is a little add on: I found about 3 of those C455IP base stations with older firmware, where you do not have the option to select VoIP for outgoing calls. At first I tried to upgrade the...
  15. Replies
    41
    Views
    34,847

    Ok, this is very interesting: Two things I...

    Ok, this is very interesting:

    Two things I figured out today;

    1. Call Transfer:
    I again looked at the manual of a newer IP gigaset, to try and see how to initiate a call transfer with the "R"...
  16. Replies
    41
    Views
    34,847

    Hi Kev - good news: I got the C455IP working in...

    Hi Kev - good news: I got the C455IP working in terms of receiving and making internal and external calls (I suggested to use ATA's, but for a few bucks extra they might as well buy SNOM300's and not...
  17. Replies
    41
    Views
    34,847

    yes, it does have some settings about DTMF / SIP,...

    yes, it does have some settings about DTMF / SIP, the link below provides a reference guide to the GUI, the images are not that clear, and there is not much elaboration on the actual settings other...
  18. Replies
    41
    Views
    34,847

    Hi Kev - thanks, my original quote to customer...

    Hi Kev - thanks, my original quote to customer was for SNOM300's all round. They do not really need portable phones, however the customer has had the wool pulled over their eyes a few times in the...
  19. Replies
    41
    Views
    34,847

    Thanks all for the tips on how to register these...

    Thanks all for the tips on how to register these units, I have a customer who wants to try and use his left over stock of C455IP sets.

    So here is the jist: They register on the Epygi (Q6L on...
  20. Replies
    1
    Views
    1,738

    The system needed to be changed to PBX in the KSE...

    The system needed to be changed to PBX in the KSE configuration hidden page. That problem solved.
  21. Replies
    6
    Views
    12,815

    Has there been any further development? I have a...

    Has there been any further development? I have a customer asking about integration to Microsoft CRM - they would need a Q32X from a user perspective, with call center features (ACD) activated.
    ...
  22. Replies
    1
    Views
    1,738

    Default Attendant routing fails

    Hi all

    I configured a new Q6L last week (current software release), set up 1 analogue trunk and 2 user extensions (SNOM300).

    When I made test calls, i can call internally between extensions, I...
Results 1 to 22 of 22