Search:

Type: Posts; User: ppvote

Search: Search took 0.01 seconds.

  1. Replies
    0
    Views
    1,714

    Siemens S685 config

    I have a Siemens S685 remotely to my phone system.

    It has logged on fine, and can receive calls fine, but it can not dial out.
    If I look in the unsuccessful call logs, then I can see it...
  2. Thread: Hacker attempts

    by ppvote
    Replies
    51
    Views
    28,435

    Recovering call costs

    I have found out today that someone has hacked our system and been making outgoing calls costing us around £70 per month... I have an IP address, which I am now blocking and have blocked...
  3. Replies
    4
    Views
    7,247

    IS there now a TAPI interface, or a Goldmine...

    IS there now a TAPI interface, or a Goldmine integration?
    Thank you.

    Dominic
  4. Replies
    41
    Views
    34,760

    I was hoping the 'call transfer' bit at the...

    I was hoping the 'call transfer' bit at the bottom may help...

    Here is another issue for you with these otherwise good phones.

    Have you tried the S450with a headset?
    When you plug in the...
  5. Replies
    6
    Views
    15,626

    Potentially I am looking at getting DDI's in a...

    Potentially I am looking at getting DDI's in a couple of other countries.

    Primarily the US and also Australia... do you think it is best to find a SIP Trunk provider local to that country and rely...
  6. Replies
    41
    Views
    34,760

    Here is a quick screen shot of the new options,...

    Here is a quick screen shot of the new options, but I don't think this really helps - as said before - I have been told the best thing is to get as many people to put in a request through their...
  7. Replies
    41
    Views
    34,760

    OK - spoke with Siemens and IT DOES NOT do...

    OK - spoke with Siemens and IT DOES NOT do re-INVITE or REFER.. the ONLY 'sort of' hold you can get is to hit the button that says INT (as if you were going to transfer to another handset on the same...
  8. Replies
    41
    Views
    34,760

    Well the bad news is that even on the latest...

    Well the bad news is that even on the latest version of firmware (020810000000/041.00) the Siemens phone does NOT HAVE a special key for Hold / Transfer

    The soft keys go to Ext (which will allow...
  9. Replies
    41
    Views
    34,760

    Indeed you get a refresh LONG before it has had a...

    Indeed you get a refresh LONG before it has had a chance to connect. Press f5 in your browser to refresh.

    I do have issues with mine sometimes if I do a power cycle - I am set up as a remote...
  10. Replies
    3
    Views
    13,668

    http://www.ppvote.com/epygi/phone.jpg

    http://www.ppvote.com/epygi/phone.jpg
  11. Replies
    3
    Views
    13,668

    QCM - 4.1.7Quadro Boot loader: 3.1.31/Release...

    QCM - 4.1.7Quadro
    Boot loader: 3.1.31/Release
    Firmware Version: 4.1.28/ReleaseAlso is it possible to run QCM on the same extension as you have a hardware phone on so that you can use QCM to manage...
  12. Replies
    3
    Views
    13,668

    I put QCM on my machine before the keys were...

    I put QCM on my machine before the keys were registered on the box and the trial period expired before our install company updated it.

    Now there is no audio controls under the dial button, and if...
  13. Replies
    2
    Views
    3,770

    Sorted on this one. Our tech support managed to...

    Sorted on this one. Our tech support managed to check the logs when I dialled and found that my phone was pre-pending my local area code on VoIP calls, which was causing the problem.
  14. Replies
    2
    Views
    3,770

    I have a Siemens Gigaset S450IP at home and we...

    I have a Siemens Gigaset S450IP at home and we have a 16x in the office. The phone is connected over the internet and people in the office can dial me fine, and can transfer calls to me.

    I can not...
Results 1 to 14 of 14