Search:

Ok I think I have it now .. but where do you do this: "In Quadro you would put an allow of the asterisk IP address for SIP communication" what menu ?

not really.

We use Switchvox a commercial ver of asterisk. You normally have to set up a PEER connection first so that the connections are authorised ie. with peer ID's and user / pass etc.
...

Sorry for asking this but can someone jog my memory.

I want to setup a peer with our main asterisk server so both offices can dial each other internal extensions. Did have this setup a year or so...

I should also note another important thing:

The simple act of plugging in the Quadro 2X unit to the PSTN Phone side of the ADSL filter IMMEDIATELY causes the modem to drop it's connection and re...

phone calls are fine .. filters, any 3 of the diff ones i have tried to rule out a bad filter, works fine and correctly isolate the ADSl freq so as to not interfere with phone calls.

All phone...

While ADSL is a separate service it is still a Frequency over the same PSTN line as your phone service and is open to line interference and line degradation problems. Any interference or equipment...

I dont think you understand ??

Nothing to do with the networking or ethernet.

I am talking about when I plug the Incoming PSTN Phone line socket of the 2X unit into my house hold PSTN phone...

I have an issue with a 2X unit

Phone line from street direct to ADSL central filter "line connection" . only equipment connected direct to the "Phone" connection on the ADSL central filter is...

Fantastic , can't wait

Thanks

Any word if this feature might find it's way into a future release. We find our test Epygi ok , but without allowing home office users to log onto call queues we have to look at other systems like...

Actually think i found what's causing it (but not the solution) . only happens on the Polycom extension not the Snom's

No ext 11 all are 3 digit 2xx

Ok when I dial on speakerphone the recorded time number 1194 the call gets placed fine

dial 1194 , press dial and get connected

If I pickup the handset and try the same number 1194 , I...

will do, i'll turn stun off and get logs and also with stun on

I have forwarded all SIP and UDP ports to the Quadro unit ? should that not mean I don't need stun ?

I had previously turned stun off to see if it made any difference , it did not so I tuned it...

Mail ? I thought it looked like a lot of NTP activity (time server)

I'll email the logs

OK did the capture ... seems to be a constant NTP stream ?

Screen shot attached

Also I had an entry

Source: x.x.x.x "the Quadro"
Destination 76.203.76.25
Type: SIP
info: request:...

I dont have the facility to do a network capture

thanks

But the connection is between the remote Quadro and our main office Switchvox server. All other ISTP trunks are fine ... only the asterisk trunk thats doing it. The Asterisk SIP time I...

OK found the source.

On my ADSL modem I can block traffic ... I blocked the 2Kbps stream and the connection to the main office Asterisk server stopped working.

My question now is ... Once you...

"this continual traffic was not present before the Quadro was on the LAN"

I mean prior to installing the Quadro this was not happening

Re port scan: this started happening immediately when the...

2) SIP timers are set to standard

3) NAT traversal was set to automatic , I have turned this OFF (made no change)

The Quadro LAN has nothing but IP Phones 6 off them 3 Snom, 1 Aastra , 1 x...

1) re extensions and sip server , I have disabled all external SIP registration for extensions and we are talking 20 meg a day to the WAN internet external to the ADSL modem

it is not a...

Yes refreshed the page ... no call is shown

when I go to Main / home and see the "Active calls list"

FOX calls show up BUT when I make a VOIP call via a VOIP provider setup in the wizard .. the call does not show up in the active call...

After first installing the Quadro 2X unit I noticed something that has never been present with any other VOIP PABX we have tried.

A steady constantly pulsing light on the router ethernet port that...