Search:

Type: Posts; User: quadroconfusion

Search: Search took 0.02 seconds.

  1. Unfortunately I did not capture straight out of...

    Unfortunately I did not capture straight out of the Epygi's LAN nic.

    I believe the Epygi is going directly into a switch port on a cisco router, and that cisco router has another switch port going...
  2. Extension 15 is just an example. The issue...

    Extension 15 is just an example. The issue appears to happen on all handsets as far as I can tell.

    The Epygi does show packet loss during the call, where the wireshark of that same call shows no...
  3. http://i.imgur.com/s4pFJdZ.jpg...

    http://i.imgur.com/s4pFJdZ.jpg
    http://i.imgur.com/RuzbSRz.png

    G711u is the preferred codec on both the handset (SPA941), and the extension settings on the quadro.

    The call statistics show the...
  4. Quadro6L frequent packet loss - Navigating the web gui makes it worse?

    I've got a Quadro 6L setup with a couple of SIP accounts for inbound and outbound VoIP calls. The system also has ~15 IP handsets connected.

    This is a common setup that has worked fine for...
  5. Incoming calls showing as PSTN1-? / anonymous

    I have an issue with a Quadro4L unit where all incoming calls are showing up as "PSTN1-?" in the call statistics, and showing as "Anonymous" on the phone handset.

    FXO settings and call routing...
  6. AASTRA - disable missed calls/edit mac.cfg?

    I am trying to use the feature
    "missed calls indicator disabled: 1" to disable missed calls for AASTRA 9133i's connected to my Quadro 6L. This feature can only be set in the mac.cfg file, and I...
  7. HotKeyCall - Where is dialplan stored? / Copy dialplan

    Hi.

    I am trying to figure out where the dialplan data is stored for HotKeyCall, so that it can be copied to another user's machine, instead of having to re-enter all of the dialplan rules again.
    ...
  8. Busy call forwarding and DND conflict? Can't have both?

    Using a Quadro4Li + Snom320 phones.

    I currently have a call route so that any incoming calls on a certain number go to a certain extension. A busy call forwarding rule is enabled so that if the...
  9. I've had a chance to test this out, works as...

    I've had a chance to test this out, works as intended.

    So,

    ? rule with a prefix of 1, destination PBX Voicemail. Source * - FXO
  10. Auto Attendant and call routing (Press 1 instead of ext11)

    I have the following situation.

    Extensions are from 11 - 18

    I would like to turn the Auto Attendant on, and make it so if a caller presses 1/2/3 etc, the call routing table will add a prefix of...
  11. Busy call forwarding doesn't seem to work, no answer is fine?

    I'm having problems with busy call forwarding.

    I have extensions 11 through to 22 on a Quadro4Li.

    I would like it so that if extension 11 is on a call (busy), the caller is redirected to...
  12. User option for extension to go directly to voicemail?

    Hi.

    I was wondering if the following was possible..

    Is it possible to set a phone to go directly to voicemail instead of ringing first? - I need this so that the user can manually...
  13. QUADRO6L + SPA942's - Bind line buttons to FXO?

    I've got a quadro6L setup with a whole bunch of Linksys SPA941's and 942's.

    I want it so that the line buttons on the Linksys will pick up an actual FXO line, as well as share their appearance, so...
  14. Quadro6L - Make group of extensions ring + call out on particular FXO

    Hi

    I want FXO1 - FXO3.. any calls on these lines, I want them to make three extensions ring at the same time, so any of these extensions can pick up the call. (I attempted to do this via a pickup...
Results 1 to 14 of 14