Search:

Hi Kevin,
But on each Quadro you see only their own extensions. How can we define a remote extension when it is not visible at the originating Quadro ?

Hi,

1) Due to a high number of subscribers (+2000 divided between 13 M32x) and each having a PSTN number is it possible (a read it somewhere) to declare all PSTN numbers with their corresponding...

Thanks very much Kevin. What's the Aussie Reds n Whites ?

I changed my configuration. The total number of Quadro M32x = 13 and the gateway is a TelcoBridges TMG7800 with 2x32 E1.
By the way we have won the bid.
Hope the Qx1000 be available very soon,...

Thanks. I spoke with IT-Logic last week. I have a few questions :
1. can the have more than one QX1000 in a network and be considered as one IP-PBX ?
2. what is the total number of intitial IP...

Hi,

At ITEXPO East 2011 held February, 2-4, Epygi has introduced company’s new Epygi QX1000 that is capable to support up to 1000 IP extensions. My question is when will it be available and what...

Thanks

Hi Kevin,

Thanks and it make sense. Can't test it yet because it is a commercial proposal.
First phase : 641 users (not a company but normal users at a site with x buildings) and traffic can be...

Hi hrant,

Aditional questions. Is it possible to do a mixing of licences on the Quadro M32x. For example 2 licences of 64 and 1 of 32.
Do you have an example of call routing configuration ?
...

Good morning,

I'm making a proposal for +2.000 subscribers located in about 60 sites (all in the same city).To reduce cost I was thinking of using 1 QuadroM32x for 4 sites (around 150 subscibers)....

Hi Kelly,

Found it very helpful and with all information regarding Epygi product line included.

Thank you.

Daniel

Looking at your power point presentation "Epygi Quadro Features" I saw the mention of the IVR Builder, but could'n find it anywhere.

Any idea when it will be released ?

Thanks and best regards,...

Hi Epygi community,

I've been surfing these forums for a while now, and I have found great help from Epygi staff members and all others (distributors Resellers etc..)

Great thanks,

Daniel:).

Hi Kevin,
Found the answer, just have to create a new rule for each allowed incoming call number and route it to extension 34. If no match, call will go to the next rule (with time/day stamp...

Thanks

Where can we change this message. By default it is in English and we would like it to be in French.

Hi Kevin,

Attached to this message the needed information (hopefully)

Best regards,

Daniel

Hi Kevin,

I've unchecked the filtering for extension 34 but the situation is still the same.

Regards,

Daniel

Hi Ashot,

This is a simulation in our labs. Incoming calls destined for 0174760047 (commercial department) reach extension 34 (row 4 of routing table) during normal working hours.
After working...

Extension 11 has "follow me" activated to ext. 14 located at a remote office.
The same ext. 11 has date & time rules acivated (09h - 19h) at the call routing table.
Question : can we add exceptions...

That is the case. Thanks

Incoming SIP call to quadro extension. The called partie receive the voice message "Please wait, we are trying to contact the person you are calling to". Where is this coming from ? Normally we...

Hi Steve,

Turn off "Enable firmware version control " and leave your "Line settings" with Snom 360. Firmware version 7.3.30 works perfectly.

Best regards,

Daniel

aYenaCom...

Had the same problem but Snom advised me to use version 2.09 (beta version). Using it for a couple of months without any problem.

Daniel

It seems to be a Snom M9 problem. At Snom forum there a lot of talk concerning this problem.

Daniel