Search:

Type: Posts; User: thodgen

Page 1 of 2 1 2

Search: Search took 0.03 seconds.

  1. Replies
    0
    Views
    1,002

    FXO trunk configuration guide

    First time using FXO trunks on a QX50. I believe I'm configuring them wrong, and I'm looking for any detailed documentation on how to configure them correctly. Using both FXO ports. I initially...
  2. Replies
    1
    Views
    975

    Dial timeout on a Polycom VVX phone

    I have what I think is an improper behavior. On a Polycom VVX Phone, I press the first line, I dial the digits, and they match one of my dial patters in Routes. However, the call doesn't start...
  3. Replies
    1
    Views
    1,665

    Probably easier ways, but you could build each...

    Probably easier ways, but you could build each FXO into a different route and give each a route code. Example, to use FXO1 dial 7 + 10 digits, to use FXO2 dial 8 + 10 digits.
  4. Replies
    2
    Views
    4,052

    This post is from several years ago. Is that...

    This post is from several years ago. Is that still the recommendation for this error code, or are there other more current suggestions.
  5. Replies
    3
    Views
    1,688

    Thanks Levon. I'll give that a try.

    Thanks Levon. I'll give that a try.
  6. Replies
    3
    Views
    1,688

    QX50 ITSP Password Issue

    I am trying to setup an ITSP for a QX50. The account password for the QX only allows for a weak password of numbers, while the ITSP requires a strong password that has at least one uppercase letter...
  7. Replies
    2
    Views
    1,608

    Thanks Levon! I appreciate it!

    Thanks Levon! I appreciate it!
  8. Replies
    2
    Views
    1,608

    Dial plan Timeout for QXFXS24

    I've looked at former forum questions regarding a dial timeout feature for fxs gateways. Most indicate it is under Telephony Dial Timeout. I'm not finding this setting within the QXFXS24...
  9. After factory reset default username and password doesn't work

    I have a large project that requires some temporary gateways. I purchased 4 used QX E1/T1 hoping they would get me through the cutovers, with new QX E1/T1 replacing them long term. Of the 4, three...
  10. Netcapture for extended period on a T1 Gateway

    I am wanting to do an extended packet capture on a T1 Gateway. Two issues - when the system times out, you log back in, sometimes the capture file is not displayed for download. Not sure where to...
  11. Replies
    1
    Views
    2,657

    T1 Gateway ECM for fax

    Is there a method for turning off ECM in the Quadro T1 Gateway. I don't seem to find it.

    I have an issue with Freeswitch T.38. With another brand of gateway I was able to resolve by turning ECM...
  12. Replies
    0
    Views
    3,083

    Quadro T1 Gateway

    When looking at Diagnostics logs, L3 data, is that data the actual data received from the far end, or is it manipulated.

    In particular - my logs show "Display name -> Empty". The carrier is...
  13. Replies
    2
    Views
    4,396

    We have a Meridian 1 option 21 connected via a...

    We have a Meridian 1 option 21 connected via a dual T1 PRI to a third party PBX. We have the Nortel setup as User, and the Epygi as the Network in this implementation, and can pass calls through in...
  14. Replies
    1
    Views
    5,018

    callers get outbound dial tone

    I have a scenario where T1 Gateway is forwarding all calls to another PBX. When call is answered by the AA, and transfered to an extension that does not have Voicemail configured, after the...
  15. Replies
    4
    Views
    2,440

    The Solution here is that you have to have a...

    The Solution here is that you have to have a separate TFTP server for the Polycom PHones to pull their Firmware and Bootrom from.

    TO resolve this issue, I setup a TFTP server on a laptop, set TFTP...
  16. Replies
    4
    Views
    2,440

    Polycom Firmware on 2x

    I have Polycom Phones that are unable to find current firmware on the 2x. Is this by design, or is there a method for placing the firmware on the 2x device either through a configuration screen...
  17. Replies
    0
    Views
    2,589

    Quadro E1/T1 with SipFoundry sipXecs

    I've recently completed the integration of SipFoundry sipXecs open source PBX with a Quadro E1/T1 unit. Works great from an interoperability standpoint.

    The system is using LinkSys SPA942...
  18. Replies
    3
    Views
    6,742

    Broadvox configuration notes

    I'm looking for configuration parameters/notes for configuring Broadvox on Epygi. If anyone has successfully configured this approved ITSP, would you be willing to share your experience and...
  19. Replies
    6
    Views
    7,527

    Within the User interface, I suggest an option to...

    Within the User interface, I suggest an option to display the Internet PSTN providers in one simple table that shows the name, userid, password, Address.

    Additionally, I believe a field needs to...
  20. Replies
    4
    Views
    2,954

    Sorry, I've been masking the true number, and I...

    Sorry, I've been masking the true number, and I was not consistent in how I was masking it. Neither are the true number.

    Your suggestion did indeed do the trick.

    Here is a summary of what is...
  21. Replies
    4
    Views
    2,954

    Thanks for the response, I really appreciate it....

    Thanks for the response, I really appreciate it.

    [QUOTE=hrant;13228]Assign 4154586969 to ext. 99 as the SIP User Name. QUOTE]

    Unless I'm mistaking your comment here, the SIP User Name is a part...
  22. Replies
    4
    Views
    2,954

    Manual ITSP receiving 404

    I thought I understood the IP Carrier route setup, but obviously this newbie doesn't.

    I ran the Voip Carrier Wizard, which created an ext 99. It also created two lines in the Call Routing - one...
  23. Replies
    1
    Views
    2,204

    Fault and Lan Lights flash at same time

    Here is the symptom - fault light comes on. The busy, fault and LAN lights flash at the same time, and then the Busy and Info light come on and the process repeats.

    Does this require a factory...
  24. Replies
    4
    Views
    2,540

    Yes - Quadro is running 5.1.6, snom's running...

    Yes - Quadro is running 5.1.6, snom's running 7.3.14

    Curious if it could be the line settings. Wondering if the line appearances actually look like a line in use.
  25. Replies
    4
    Views
    2,540

    snom 360 (3) and snom 370 (1)

    snom 360 (3) and snom 370 (1)
Results 1 to 25 of 26
Page 1 of 2 1 2