PDA

View Full Version : new epygi release 5.3



nitrox
02-28-2012, 04:42 AM
is it possible to know when are you going to release the firmware version 5.3?

thanks in advance for your reply.

Ashot
02-28-2012, 05:42 AM
It's depend on what specific product you are asking for. Specifically for 32x and 8L/26x/12Li/26xi the 5.3 FW will be available by the end of the current week(02 March 12). for 2x/4x/16x by the mid of March. At the moment i don't have strict dates for other products

waipapaeyecare
04-10-2012, 03:50 PM
Any update on these dates esp for the 4x?

Cheers

Ashot
04-13-2012, 02:54 AM
The 5.3 FW for 2x/4x/16x will be available during the next week (16-20 March)

Thanks
Ashot

Ashot
04-13-2012, 03:10 AM
Sorry for mistake, I mean 16-20 April

Thanks
Ashot

ASL-Support
04-23-2012, 05:34 AM
I have not seen the 5.3 firmware yet, is it delayed? (for the 4x product)

hrant
04-25-2012, 01:59 PM
not yet, will be published in the next few days.

Ashot
04-26-2012, 06:21 AM
The 5.3.5 firmware for 4x is published on the web

tilefono
11-07-2013, 09:39 AM
Will the 5.3.53 firmware be released for the up to now supported 2x(i), 16x(i), 4L(i), 4x, 6L models?

Regarding the 4x the last available software I can see is Quadro4x Software 5.3.20.

Ashot
11-08-2013, 02:05 AM
Actually the firmware version numbering is different for different products. So it isn't clear what you mean by "5.3.53 firmware...for ... 2x(i), 16x(i), 4L(i), 4x, 6L models"?

The last of available firmware versions are:
for 2x(i) - 5.3.23
for 4x(i)/16x(i) - 5.3.20
for 4L/2x2 - 5.3.21
for 4Li - 5.3.20
for 6L - 5.3.20
for 32x - 5.3.53
for 8L/12Li/26x/26xi - 5.3.53
for QX1000 - 5.3.31

tilefono
11-18-2013, 12:49 PM
Well Ashot,

We were quite aware of what the latest firmware versions were for the various Epygi models out there, but thanks for putting them all on a single page.

As you will undoubtedly have noticed the 2x(i), 16x(i), 4L(i), 4x, 6L models have been stuck on a 5.3.2x release, whereas the 8L/12Li/26x/26xi/32x have moved on to the 5.3.53 release.

Since I intend for my question to be very specific this time around, here it is:

When will the 2x(i), 16x(i), 4L(i), 4x(i), 2x2, 6L models, be upgraded to a newer code version, which will include support for these features:

• New Overall Calling Time Limit feature. This feature allows a total call duration for all calls to be configured over a specific time frame for each Call Routing entry. Once the total duration has been reached, the entry can be disabled, allowing calls to use the next available route.
• A new feature code for FXS phones. While on a 3-way call, pressing FLASH+0 allows the user to disconnect from the call while the two remaining participants stay connected.
• Added RTP Channel option in the Attendant Ringing Announcement.
• An option in the generalconfig.cgi hidden page was added to remove the "Diversion" header from SIP Invite messages sent out from the Quadro. If an incoming call is being forwarded back to the PSTN, the Quadro will add the "Diversion" header into the outgoing SIP Invite. However, many ITSPs do not support this and reject the call if the "Diversion" header is present.
• PnP and auto configuration support for new IP phones: Aastra 6737i and Yealink W52P.